Sunday, November 22, 2020

Toro Tine holder storage stand



Recently on twitter I seen this . What a fantastic idea to Free up a confusing mess in parts room .It will keep it all together and organized . Original Build by @DiarmuidGriff (twitter handle ) 

If you have a new welder and would like a nice easy creative build this would be a nice project to do . My build was modified for what I would like to use it for but basically exact same idea as original build . Took some measurements and started welding it together .Mines about 4' high. 


Using the block tines you can lay out the mounting bars pretty quickly . Welded in 3/4" bolts to hold tines. 


Casters I just tac and weld in place .If they fail in the future I can just grind them off to replace . Cheap casters rolled well . Wasn't overly heavy.



These magnets are very handy to square things up for welding . I added baskets to keep spare tines in 
 

Paint booth lol . Hanging projects under my lift so I can paint all sides at he same time 




Add my hand tine bars to rack to . Also easy build . In the past I made the block end until I figured out I already had the blocks so why not just make handles for them ? Looks great . metal stock I used was 1.5" square tube stock , 3/4"x 3" bolts ,and 1.5" angle , primer paint and red paint .

Great east Build .Well done Diarmuid .

Thursday, October 8, 2020

Toro HDXD shifting lever repair

 One of our 3 HDXD Workmans has always had a shifting problem since new . I've adjusted it many times with out much success . Recently something let go completely and had to be investigated . 

Here is a little trick to do so you done forget that you have the safety bar installed on ram . 


Remove seats ,back pan, and seat cab to get to the shifter asm . Seats probably the worst to get off .

remove shifting cable ends and one through bolt holds ASM in . 

Tearing it apart on the bench . It's pre loaded with grease so its a pretty messy job . Checking springs and pins for wear .

Some wear but couldn't see what was causing the problems . Notice the half washer in picture ?

Wasn't in parts book .Noticed it was actually the frame mount . The slotted section is wear shifter assembly locks in and through bolts goes through broken section . See the 2 long bolts, when finished reinstalling adjust them so they don’t over travel shifter cables causing gear lock up or shifting issues. Should be adjusted at end of gear lever travel on transmission end . 2022 I replaced the shift Asm and resolved the gear lock up issue I’ve had on this unit since new. 

After cleaning all the parts off I decided to trim a little more rubber casing  out wear it mounts .

Like so .

Next welded in the broken piece.

And reinforced the top so it can't bend and break off again . Original mount looks pretty weak for the amount of abuse it has to take in the reel world .  

Getting ready to install it back into the machine . See these 2 wave washers . They where in between assembly and frame . I'm putting them on the outside against frame where I think they should have been . Now thinking this was the problem all along ! might be looking to do the same to top dresser this winter ,its also slightly finicky . 

Used my claw to get wave washer in through access hole .and installed a new nylock nut . Wave washers are there to keep a little tension on shifter caseing against frame but not so much to crush assembly . 

All in . Feels good . Actually feel it going into gear with out binding 







I just squished a full tube of grease in it . I think it acts as a seal and lubes the  mechanism.

Reassemble everything . It was out all day today with no issues . Staff where saying its the best one now to shift . 

























Sunday, July 5, 2020

JD 7400 forward pedal sensor wire Parts issue

This has happen twice now . One of the 7400 is used for cart path edges on tree side of course . Usually it's the one operator that does it and he knows where every issue is on this labor saving job . Recently went out with a new operator and it struck an object on front right deck bending the lift arm to deck bracket. So this time it came up and sheered a few forward peddle sensor wires and crushed the rest .  


Last time his happen I ordered the connector but to my surprise there are NO connection pins inside for replacing the damaged ones on machine . machine wound up going back to dealer to get a new brain  separate issue. They had a chuckle at the Mickey Mouse repair they had to redo . Same deal this time . Asked again (more than once) about if the connecters are available for purchase to no avail. So back to square one and made the repair the best I could using the old connections and trying to pry them open to reuse .   


Deutsch type connection I found out after spending many hours reaching out on twitter and web searches . 6 of them I managed to reuse 1 of them got launched across the shop and managed to find and the last one snapped in 2 pieces but it took solder well to hard line it into connection. 


cut them all even to be regripped to reuse 


Setting them in the vise so I could put a lot of down pressure with a pic I was able to spread crimps open on 5 of them 


Half done here 


Finished it up with one soldered connection . No codes came up when I tried it . 


I'm posting about this repair because I find it idiotic to go through so much foolishness to what should be a simple repair . That connection plug with out crimp on connections included is a big waste of everyone's time  John Deere ( mine , sale/parts/service peoples )  . For the price of it it should come complete . Course lost a weeks plus use and for what should have been a half hour job with proper parts . I managed to locate those connection crimp pins on line and ordered them for future repairs . 

Oh on my quest I noticed all connection plug in COME with the repair crimp on pins too in other mechanical fields  !

Wednesday, March 25, 2020

XUV 885D frame front end straightening

On the John Deere XUV 885D we purchased the trac system to groom trails and gives us mobility during the Winter season. The trouble is there is more mass to move and can be hard on clutches and front ends if you're not careful. I don't think this machine was originally designed for this option. Follow the instructions for use with tracs or you may bend up the lower control arm frame mount. If a curb is hit on front corner of front tracs it WILL bend things up if you're going full speed. Last winter one of the guy's lost controls on ice and dinged the front up pretty good. Tracs DO NOT like ice and recommend not taking it out in very icy conditions. 

Purchased this kit at Princess Auto on sale .169$? from 289$ paid for itself on this one repair ten times over. 


My Delima lower control arm pushed back twisting framing. Trac's kit has re-reinforcement plating that bolts on it. Trouble is instead off snapping lower control arm it bends the frame. Right front


Left front looks good but steering is all out of Wack and alignment from by temporary repair to keep it grooming.


A few degrees make a big difference 88.84


impact on front end of trac moved control arm back enough to tip it in at top towards machine.  85.45 


Sleeved hole in frame I installed grade 8 bolt and washers to push off of. 


Control arm I installed a piece of angle to hold bar in place. Push slowly and watch mount points to see what's going to move. This worked excellent on this set up. Total control. Pushed it past the point I needed by a degree or 2 for spring back. 


Looking at these holes in control arm framing I decided to add a little more support.


More picks

   
bolted angle iron in and welded the final point. Removable support 


   
Almost done 

  
Looking great

  
Lots of room for skid plates to go back on 


 Alignment next . 

Ends and bar used from kit 


Pressures off . Readings 


I'll take it. 1000% better than tree chain method. 


Lining things up 



Looks great 


Now back to regular service work on her. Highly recommend this kit. It is 10-ton kit and easily moved things back in place.  






Thursday, March 12, 2020

Toro HDXD rear wheel bearing (Aftermarket)

We have 3...... 2015  HDXD 600 to 1000 hours .They have gone through many rear wheel bearings .I have never seen these similar type bearing go so quick on other equipment in the past . Hauling heavy loads on paved cart paths with the crazy tight turning abilities of them might be the cause or cheap out sourcing of parts in production . Take your pick . All I know is that they have been changed out twice under warranty and now it's my problem !
Last time I checked a few years ago the OEM bearing was near or over 600.00$ Canadian .Last year looking around I found the local auto choice had them for 153.00 $ but needed some customizing to make it work .Held up for a few seasons and still tight as the day it was put on . 
After checking the last unit on the lift I noticed a little play in one rear OEM bearing AGAIN. Wajax had this bearing for 171.00$ .  



This bearing works with a little customizing . OEM Bearings are front access and these are rear access....so

Metric studs . you will need 12m x 1.75 hub nuts . OEM ones will go one but don't be fooled they are slightly different and will strip out over time . 

  
Drill out just enough to take threads out 

  
Drill a 7/8" hole with carbide hole drill bit . I used a 1 " the first time but I think this will be big enough to get front access .


Off set so your not drilling into flange .Some Timken hubs have flush mounted studs . This one did not so the hub bolt heads may need a slight grind to get better clearance . 


and done .

This ones been on for over 400 hours a record .I even painted it red for my experiment . A little reworking to save 400$ to last longer than the OEM ones .....I'll take my chances .