Saturday, August 23, 2014

Toro MD blown head gasket


Recently had the MD for regular service . These machines have no oil filter and oil change intervals are at 50 hrs. Noticed the head gasket was weeping out oil . I had posted on twitter about the repair at the 236 hr mark . Received a few favorites and questions about if it was covered under warranty or why I was doing the repair .We it's like this . The dealer is a good 3.5 hrs. away and I enjoy my job so much and organised enough that I'm willing to do the warranty repairs myself . Under the direction of Bill at Veseys they are usually fairly easy repairs . Believe me it has it's perks most of the time . 


Not quit blown head gasket but soon . 


Really like the spring clip set up on the exhaust .


Made removal very easy . 


You can leave this part of exhaust manifold on .


Carburetor was just as easy to remove leaving all the cables attached . 


I wrapped a rag around it to keep dirt out till assembly .


Next turn engine till you see that both rocker arms have play . Then remove the pin that holds them in place . Easy design on the Yamaha engine . No clips etc. the valve covers is what holds the pin in place . 


Lay the parts out in such a way that you can assemble them back in the same location . 


I have a heavy flat bar that is used with med emery cloth to evenly remove gasket material . I noticed the cylinder was ever so slightly of in the blown gasket area . I kept removing material in 8 different directions till it all looked flush . 


Head looked pretty good . To make sure it's flat and square I use my bench plate with a large piece of emery cloth and work the head against it in a figure eight pattern . Ready for assembly .


You can see the guides in valve cover that hold the rocker arm pin in place. So simple .
Assemble in reverse order . I did torque the head down carefully to 15 ft.lbs. first then to 36 ft. lbs. Always torque in a cross bolt pattern . 

I did notice that the head shield has tabs to hold the valve cover gasket in place . Also there is one longer bolt for the dip stick tube side on valve cover . Took it for a run and it worked great . No leaks.1.5 to 2 hrs . taking your time and keeping things clean and organized. Over all not a bad job and can be done in the machine . 




Wednesday, August 20, 2014

Toro 4300 section valves bolt kit

The newer 4300D always had an oil film on the section pumps . I posted on Golftechs asking for the torque specs . to see if the bolts where in spec . 




After remove the front bracing I had found the problem.Stud was snapped off flush with section valve .


 Looks like it has been this way for a while . Apparently this happens fairly often .You may want to check your 4300 . Bolt kit was in stock at Veseys and where sent out next day.


First I drain the hydraulic oil tank . I keep a few empty pails sealed just for this reason . Would hate to loose or contaminate the oil before its due to be changed . I drained a good 35 liters out .  


Mark the lines to section pumps . I let the inside wrench rest on the nut so it made hose removal easy . Remove all the lines .


Then use the Allan key and an wrench for better leverage to get the 2 bolts out that hold the section pumps to hydraulic pump .


Pump just pulls out there is an O ring on the end or in the pump . 


Here is what it looks like with it removed . 


Put the unit in the vice to hold for repair. The idea is not to move the sections out of place while the bolts and studs are out . 


Picture with end cap removed . You can see the broken stud now and can be removed with vice grips  . 


Stud should come out fairly easy. 


End cap. Keep everything clean when assembling .


I torqued the studs and bolts in two stages 15 ft.lbs. then 33 


Ready for install.


Well almost . One of the bolts were longer ? The other one sits flush with bottom plate .


Trimmed it off with a cut off wheel . Then installed the new seal .


Pumps back in ready for lines to be hooked up I used a dab of sealer for hoses . I installed the front support bracket before hoses . 



Done . Refill the hydraulic oil tank then start machine a let idle for 15 minutes . Check for leaks . Take your time and keep everything clean while doing this job . Over all fairly easy . Might have lost 100 ml of oil. 1 to 1.5 hours job.

Tuesday, August 19, 2014

Toro sidewinder ..Sidewinder Hydraulic Ram Replaced

Recently our sidewinder flipped over in a trap . After getting it going and running for a while I noticed a leak under the machine . The ram may have bent and a new one was ordered . This hydraulic ram can not be rebuilt . 


New part arrived today ready for install . It was about an hour job having to free up a few parts .


Take the left wheel off .The left step plate has to be removed to get the pins out .


Access plate on top same side also will have to be removed to get at hydro lines and nuts . 


You can just see it tucked in pretty good behind framing . 


Pin for ram being removed . The pin to the right will also have to be removed. 


Reaching through the access panel I was able to remove the lines . Cap them off to keep oil in and dirt out . Remember where they go .


I had to work on this pin a bit to get it out . The lock tab was also broken off and needed welding . it also has a cir-clip on the bottom . 


Next..... if unbolt these 4 bolts you can just slide bracket and ram out . Be careful not to damage the threads for hydraulic lines .


Exchange parts to the new one on the bench . This pin also has a cir-clip . I don't think the pin can be removed on the machine .While exchanging parts I noticed a fair amount of wear which will be recorded and fixed this winter . 


Reassemble in reverse order . 
Over all fairly easy... just takes some patients to get all the parts and ram to slide back in and lined up . 
  


Thursday, August 14, 2014

Toro boom valve kit


Sprayers are used more and more on golf courses . We have 2 of them here and older 2001 and the Windfoiled 2011 Toro 1250. Last week they were both out of service temperately . Thanks to Bill and the crew at Veseys we were up and running in no time .

I had installed a boom valving upgrade kit  a while back which had solved our dripping boom issues . Last week they started dripping again . Lucky for us we received the rework kit .


Well packaged sealed up with molded foam padding . 


Straight exchange of parts . Just mark the boom lines and remove wire connections, hoses and clamps . 


After removing the old part ,the kit came with a couple of shims to go over bolts . 


15 minute job from start to finish . Ready to hook it all back together.


And done . Now to take it over to wash rake and half fill the tank . The tank pressure and boom pressure will have to be adjusted . 


She's ready to work . The spray tech get a laugh because I call this one the USS Enterprise ( Star Trek) because of it size with the windfoils . 
The Old sprayer received a new electric pump clutch . 

Runs much quieter. Looks like a tight spot but after removing a few nuts on the coupler and four more for the pump ( remove pump ) it gave lots of room to work . Have a lift really speeds this type of work up . About a 1/2 to an hour job . 


Both are up and ready . 

Losing more staff every week  , Seasons starting to wind down a little . It will time to start thinking of aerating and fall projects . 

The sidewinder developed a leak on the ram that controls the side to side movement of decks . 


Should be in soon . Still usable . The rod must have bent a little after the last mishap.

Hopefully will be getting the forecasted rain the irrigation pond sure could use it .